Abstract
Recent improvements in image segmentation techniques enabled the (semi)automatic extraction of biostructures surfaces from 3D medical imaging data. The diffusion of 3D printing technologies promoted their introduction in the medical field, giving rise to several applications, such as the development of 3D-printed anatomical imaging phantoms. These devices provide controlled experimental environments for the improvement of medical imaging techniques, as they mimic the morphological and physiological features of different body parts. However, to obtain a 3D printable model from medical imaging data, different post-processing steps are needed, which require a considerable effort. Supports generation is often a critical task, as it requires to find the minimum amount of support structures necessary to hold a part in place during the printing process. This is particularly difficult for complex anthropomorphic models, for which a high printing level of detail, along with a reasonable number of internal supports, is usually needed. In this paper, an automatic method for the design of efficient support structures is proposed, which is suitable for 3D printing of complex anatomical phantoms, even with non-professional FDM 3D printers. A custom design software was developed, which places paraboloid-shaped shells to support all and only the critical points of the 3D model. This provided different advantages over support generation by means of common slicing software, allowing a reduction of material waste and printing times, along with an easier and faster dissolution of soluble supports for the clean-up of phantoms empty volumes.
Keywords
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Oropallo, W., Piegl, L.A.: Ten challenges in 3D printing. Engineering with Computers 32, 135 (2016). https://doi.org/10.1007/s00366-015-0407-0
Bücking, T.M., Hill, E.R., Robertson, J.L., Maneas, E., Plumb, A.A., Nikitichev, D.I.: From medical imaging data to 3D printed anatomical models. PLoS ONE 12(5), e0178540 (2017). https://doi.org/10.1371/journal.pone.0178540
Rengier, F., Mehndiratta, A., von Tengg-Kobligk, H., et al.: 3D printing based on imaging data: review of medical applications. Int. J. CARS 5, 335 (2010). https://doi.org/10.1007/s11548-010-0476-x
Tam, M.D.B.S., Laycock, S.D., Brown, J.R.I., Jakeways, M.: 3D printing of an aortic aneurysm to facilitate decision making and device selection for endovascular aneurysm repair in complex neck anatomy. J. Endovasc. Ther. 20(6), 863–867 (2013). https://doi.org/10.1583/13-4450MR.1
Gargiulo, P., Árnadóttir, Í., Gíslason, M., Edmunds, K., Ólafsson, I.: New directions in 3D medical modeling: 3D-printing anatomy and functions in neurosurgical planning. J. Healthc. Eng. 2017, 8 (2017). https://doi.org/10.1155/2017/1439643. Article ID 1439643
Schmauss, D., Haeberle, S., Hagl, C., Sodian, R.: Three-dimensional printing in cardiac surgery and interventional cardiology: a single-centre experience. Eur. J. Cardio-Thorac. Surg. 47(6), 1044–1052 (2015). https://doi.org/10.1093/ejcts/ezu310
Vukicevic, M., Mosadegh, B., Min, J.K., Little, S.H.: Cardiac 3D printing and its future directions. JACC Cardiovasc. Imaging 10(2), 171–184 (2017). https://doi.org/10.1016/j.jcmg.2016.12.001
Noecker, A.M., Chen, J.F., Zhou, Q., White, R.D., Kopcak, M.W., Arruda, M.J., Duncan, B.W.: Development of patient-specific three-dimensional pediatric cardiac models. ASAIO J. 52(3), 349–353 (2006). https://doi.org/10.1097/01.mat.0000217962.98619.ab
Waran, V., Narayanan, V., Karuppiah, R., Thambynayagam, H.C., Muthusamy, K.A., Rahman, Z.A.A., Kirollos, R.W.: Neurosurgical endoscopic training via a realistic 3-dimensional model with pathology. Simul. Healthc.: J. Soc. Simul. Healthc. 10(1), 43–48 (2015). https://doi.org/10.1097/sih.0000000000000060
Singare, S., Dichen, L., Bingheng, L., Zhenyu, G., Yaxiong, L.: Customized design and manufacturing of chin implant based on rapid prototyping. Rapid Prototyping J. 11(2), 113–118 (2005). https://doi.org/10.1108/13552540510589485
Cohen, A., Laviv, A., Berman, P., Nashef, R., Abu-Tair, J.: Mandibular reconstruction using stereolithographic 3-dimensional printing modeling technology. Oral Surg. Oral Med. Oral Pathol. Oral Radiol. Endod. 108(5), 661–666 (2009). https://doi.org/10.1016/j.tripleo.2009.05.023
Parthasarathy, J.: 3D modeling, custom implants and its future perspectives in craniofacial surgery. Ann. Maxillofac. Surg. 4(1), 9 (2014). https://doi.org/10.4103/2231-0746.133065
Zopf, D.A., Hollister, S.J., Nelson, M.E., Ohye, R.G., Green, G.E.: Bioresorbable airway splint created with a three-dimensional printer. N. Engl. J. Med. 368(21), 2043–2045 (2013). https://doi.org/10.1056/nejmc1206319
Leary, M., Kron, T., Keller, C., Franich, R., Lonski, P., Subic, A., Brandt, M.: Additive manufacture of custom radiation dosimetry phantoms: An automated method compatible with commercial polymer 3D printers. Mater. Des. 86, 487–499 (2015). https://doi.org/10.1016/j.matdes.2015.07.052
Filippou, V., Tsoumpas, C.: Recent advances on the development of phantoms using 3D printing for imaging with CT, MRI, PET, SPECT, and ultrasound. Med. Phys. 45, e740–e760 (2018). https://doi.org/10.1002/mp.13058
Leng, S., Chen, B., Vrieze, T., Kuhlmann, J., Yu, L., Alexander, A., Jane Matsumoto, J., Morris, J., McCollough, C.H.: Construction of realistic phantoms from patient images and a commercial three-dimensional printer. J. Med. Imaging 3(3), 033501 (2016). https://doi.org/10.1117/1.jmi.3.3.033501
Zaidi, H., Tsui, B.M.W.: Review of computational anthropomorphic anatomical and physiological models. Proc. IEEE 97(12), 1938–1953 (2009). https://doi.org/10.1109/jproc.2009.2032852
Alfano, B., Comerci, M., Larobina, M., Prinster, A., Hornak, J.P., Selvan, S.E., Amato, U., Quarantelli, M., Tedeschi, G., Brunetti, A., Salvatore, M.: An MRI digital brain phantom for validation of segmentation methods. Med. Image Anal. 15(3), 329–339 (2011). https://doi.org/10.1016/j.media.2011.01.004
Fedorov, A., Beichel, R., Kalpathy-Cramer, J., Finet, J., Fillion-Robin, J.-C., Pujol, S., Bauer, C., Jennings, D., Fennessy, F., Sonka, M., Buatti, J., Aylward, S.R., Miller, J.V., Pieper, S., Kikinis, R.: 3D slicer as an image computing platform for the quantitative imaging network. Magn. Reson. Imaging 30(9), 1323–1341 (2012). PMID: 22770690
Lorensen, W.E., Cline, H.E.: Marching cubes: a high resolution 3D surface construction algorithm. ACM SIGGRAPH Comput. Graphics 21(4), 163–169 (1987). https://doi.org/10.1145/37402.37422
Friedman, T., Michalski, M., Goodman, T.R., Brown, J.E.: 3D printing from diagnostic images: a radiologist’s primer with an emphasis on musculoskeletal imaging putting the 3D printing of pathology into the hands of every physician. Skeletal Radiol. 45(3), 307–321 (2015). https://doi.org/10.1007/s00256-015-2282-6
Acknowledgment
Funding by the CNR Strategic Project “The Aging: Technological and Molecular Innovations Aiming to Improve the Health of Older Citizens” (http://www.progettoinvecchiamento.it) and by the Italian Ministry for Education, University and Research (Project MOLIM ONCOBRAIN LAB) is gratefully acknowledged.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Ethics declarations
The authors declare that they have no conflict of interest.
Rights and permissions
Copyright information
© 2020 Springer Nature Switzerland AG
About this paper
Cite this paper
Pirozzi, M.A., Andreozzi, E., Magliulo, M., Gargiulo, P., Cesarelli, M., Alfano, B. (2020). Automated Design of Efficient Supports in FDM 3D Printing of Anatomical Phantoms. In: Henriques, J., Neves, N., de Carvalho, P. (eds) XV Mediterranean Conference on Medical and Biological Engineering and Computing – MEDICON 2019. MEDICON 2019. IFMBE Proceedings, vol 76. Springer, Cham. https://doi.org/10.1007/978-3-030-31635-8_35
Download citation
DOI: https://doi.org/10.1007/978-3-030-31635-8_35
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-31634-1
Online ISBN: 978-3-030-31635-8
eBook Packages: EngineeringEngineering (R0)