Skip to main content
SpringerLink
Log in

Measurement of Residual Stresses in Thin-Sheet Welded Constructions of Low-Alloyed Steel

  • Conference paper
  • First Online:
Proceedings of the 4th International Conference on Industrial Engineering (ICIE 2018)

Part of the book series: Lecture Notes in Mechanical Engineering ((LNME))

Included in the following conference series:

Abstract

The concentrated heat source causes strong local heating of the metal during arc welding. The molten metal is cooled comparatively quickly. Its volume is reduced during solidification, shrinkage occurs and the density of the weld seam metal increases. During welding, the molten and solid metals are inseparable. During solidification in the weld seam metal and the heat-affected zone, changes of the microstructure take place that influence the nature of the distribution, the sign and value of residual stresses. Longitudinal and transverse internal stresses occur. When the stress value reaches the yield limit, plastic deformation occurs in the metal, and the shape and dimensions of the workpiece changes. Adverse tensile residual stresses reduce the vibration strength of welded constructions. The weld seam stresses differ in the gradient and complex nature of the distribution in different directions. The influence of residual stresses on the fatigue resistance will be different for various areas of a welded joint. Simulation and calculation methods do not accurately determine the value of residual stresses. The article presents the technique of residual stress measurement by an X-ray diffraction method. Residual stresses were directly determined on the surface of the weld seams. Single butt welds and single bevel butt welds of low-alloyed sheet steel with 0.9% C-2% Mn-0.8% Si have been investigated. The stress tensor at different sites of welded joints was calculated. The results demonstrate the influence of nonequilibrium crystallization on the nature of residual stresses formation. The interrelation between residual stresses and structural transformations occurring in the weld metal was shown.

This is a preview of subscription content, log in via an institution to check access.

Access this chapter

Log in via an institution
Chapter
USD 29.95
Price excludes VAT (USA)
  • Available as PDF
  • Read on any device
  • Instant download
  • Own it forever
eBook
USD 259.00
Price excludes VAT (USA)
  • Available as EPUB and PDF
  • Read on any device
  • Instant download
  • Own it forever
Softcover Book
USD 329.99
Price excludes VAT (USA)
  • Compact, lightweight edition
  • Dispatched in 3 to 5 business days
  • Free shipping worldwide - see info

Tax calculation will be finalised at checkout

Purchases are for personal use only

Institutional subscriptions

References

  1. Zamashchikov YI (2006) Duality in metal cutting: impact to the surface layer residual stress. Mater Manuf Proc 21:551–566. https://doi.org/10.1080/10426910500471706

    Article  Google Scholar 

  2. Zamashchikov YI (2014) Surface residual stress measurements by layer removal method. Int J Mach Machinability Mater 16:187–211. https://doi.org/10.1504/IJMMM.2014.067307

    Article  Google Scholar 

  3. Zamashchikov YI (2007) Machining residual stresses and part distortions. Int J Mach Machinability Mater 2:378–412. https://doi.org/10.1504/IJMMM.2007.015473

    Article  Google Scholar 

  4. Zamachtchikov YI, Breaban F, Vantomme P, Deffontaine A (2002) Method to evaluate residual stresses in laser cutting process. Int J Laser Eng 12:27–41

    Article  Google Scholar 

  5. Tolstikhin K (2017) An approach to differentiation of non-smooth functions obtained during residual stress measurements by layer-removal method. J Eng Math 103:87–95. https://doi.org/10.1007/s10665-016-9862-x

    Article  MathSciNet  MATH  Google Scholar 

  6. Nikolaeva EP, Nikulin DS (2016) The application of innovative means for quality control of the high-speed steel tools. MTSAM 50:73–80

    Google Scholar 

  7. Nikolaeva EP (2013) Application the Barkhausen noises method for control the hardening of details by superficial plastic deformation Izv. SSC RAS 15:428–431

    Google Scholar 

  8. Nikolaeva EP, Vlasov DB (2017) Effect of heat treatment conditions on structure and properties of high-speed steel. IOP Conf Ser Mater. Sci Eng 177:012113

    Article  Google Scholar 

  9. Nikolaeva E, Gridasova E, Gerasimov V (2015) The application of X-ray diffraction and Barkhausen noise for studying of shot peened constructional steel 30HGS Izv. SSC RAS 17:125–132

    Google Scholar 

  10. Nikolaeva EP (2016) Structure investigation of the constructional steel St3 ps after Argon-Arc Plasma treatment. In: Radionov AA (ed) Mater Sci Forum 870:500–506

    Google Scholar 

  11. Nikolaeva EP, Mashukov AN (2017) Evaluation of residual stresses in high-pressure valve seat surfacing. Chem Pet Eng 53:459–463

    Article  Google Scholar 

  12. Nikolaeva E, Mashukov A (2017) Evaluation of residual stresses in lock valve elements of petrochemical productions. MATEC Web Conf Int Conf Mod Trends Manuf Technol Equip (ICMTMTE) 129:06006

    Article  Google Scholar 

  13. Sorsa A, Leiviska K (2011) Simultaneous prediction of residual stress and hardness based on the Barkhausen noise measurements. NDT World Rev 4:78–83

    Google Scholar 

  14. Totten G, Howes M, Inoue T (2002) Handbook of residual stress and deformation of steel. ASM International, Materials Park, Ohio, USA, p 500

    Google Scholar 

  15. Viktor Hauk (1997) Structural and residual stress analysis by nondestructive methods: evaluation, application, assessment. Amsterdam, Elsevier Science BV, 640pp

    Google Scholar 

  16. Molzen MS, Hornbach D (2000) Evaluation of welding residual stress levels through shot peening and heat treating. Milwaukee, Wisconsin, pp. 1–7. http://www.lambdatechs.com/documents/273.pdf

  17. Yablokova NA (2012) X-ray structure analysis technique for stress-and-strain state analysis of compressor blades made of VT3-1 alloy. NDT World Rev 4:42–44

    Google Scholar 

  18. Yablokova NA, Trofimov VV (2013) XRA study of the stress-strain state of the compressor blades. Zavodskaya Laboratoriya. Diagnostika Materialov 1:36–44

    Google Scholar 

  19. Makaruk AA, Khamaganov AM, Pashkov AA, Samoilenko OV (2017) Studying stress state under high rigidity parts peen processing Proc Irkutsk State Tech Univ 21(4):39–46 (in Russian). https://doi.org/10.21285/1814-3520-2017-4-39-46

    Article  Google Scholar 

  20. Nikolaev AY (2017) Simulation of the plain milling process. Int Conf Mech Eng Autom Control Syst. http://iopscience.iop.org/article/10.1088/1757-899X/177/1/012080/pdf

  21. Cheslavskaya AA, Mironenko VV, Kolesnikov AV, Maksimenko NV, Kotov VV (2015) Choosing an efficient method for forming parts by means of an engineering analysis performed with the use of a CAE system. Metallurgist 58:1051–1059

    Article  Google Scholar 

  22. Mironenko VV, Polyakova OE, Sechkarenko DA (2016) Accounting for the technological history of the formation of a part in strength calculations. Metallurgist 59:871–876

    Article  Google Scholar 

  23. Cheslavskaya AA, Mironenko VV, Bersenev SA, Kotov VV (2013) Forming of tee parts by a process that combines diffusion welding and pneumothermal forming in the superplastic regime. Metallurgist 56:899–903

    Article  Google Scholar 

  24. Mironenko VV, Polyakova OE, Sechkarenko DA, Kotov VV (2016) Accounting for the technological history of the formation of a part in strength calculations. Metallurgist 59:1015–1019

    Article  Google Scholar 

  25. Senior Welding Inspection (2008) Rev 1 Jul 08 TWI Ltd. http://lecturer.ppns.ac.id/munir/wp-content/uploads/sites/14/2015/09/43859020-Cswip-3-2-Book.pdf

Download references

Acknowledgements

The authors are grateful to the staff of the laboratory “Study of technological residual stresses and deformations” of National Research Irkutsk Technical University for supporting this research and their contribution to conducting the experiments.

Author information

Authors and Affiliations

  1. Irkutsk National Research Technical University, 83, Lermontov Str., Irkutsk, 664074, Russia

    E. P. Nikolaeva & A. Yu. Nikolaev

Authors
  1. E. P. Nikolaeva
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. A. Yu. Nikolaev
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to E. P. Nikolaeva .

Editor information

Editors and Affiliations

  1. South Ural State University, Chelyabinsk, Russia

    Andrey A. Radionov

  2. Platov South-Russian State Polytechnic University, Novocherkassk, Russia

    Oleg A. Kravchenko

  3. South Ural State University, Chelyabinsk, Russia

    Victor I. Guzeev

  4. South Ural State University, Chelyabinsk, Russia

    Yurij V. Rozhdestvenskiy

Rights and permissions

Reprints and permissions

Copyright information

© 2019 Springer Nature Switzerland AG

About this paper

Check for updates. Verify currency and authenticity via CrossMark

Cite this paper

Nikolaeva, E.P., Nikolaev, A.Y. (2019). Measurement of Residual Stresses in Thin-Sheet Welded Constructions of Low-Alloyed Steel. In: Radionov, A., Kravchenko, O., Guzeev, V., Rozhdestvenskiy, Y. (eds) Proceedings of the 4th International Conference on Industrial Engineering. ICIE 2018. Lecture Notes in Mechanical Engineering. Springer, Cham. https://doi.org/10.1007/978-3-319-95630-5_261

Download citation

  • DOI: https://doi.org/10.1007/978-3-319-95630-5_261

  • Published:

  • Publisher Name: Springer, Cham

  • Print ISBN: 978-3-319-95629-9

  • Online ISBN: 978-3-319-95630-5

  • eBook Packages: EngineeringEngineering (R0)

Publish with us

Policies and ethics

Search

Navigation