Abstract
The article reports the synthesis of the concentrated Gold Nanoparticles (AuNPs) ink and its printing on the paper substrate through Office Ink Jet printer. Initially, AuNPs were synthesized from the precursor Gold (III) Acetate through Ultrasonic Spray Pyrolysis. Ellipsoidal shaped AuNPs with a size distribution of below 50 nm were confirmed through TEM and DLS measurement. Maximum absorbance wavelength of AuNPs measured through UV-vis spectroscopy was 532 nm. Further, the AuNPs ink was prepared through the rotavapour and filtered upto the Au concentration of 600 ppm determined through ICP-OES. The AuNPs printed patterns on the photo paper substrate were successfully printed and further analyzed with SEM.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Abbreviations
- AuNPs:
-
Gold Nanoparticles
- LED:
-
Light Emitting Diodes
- TFT:
-
Thin Film Transistors
- USP:
-
Ultrasonic Spray Pyrolysis
- TEM:
-
Transmission Electron Microscopy
- DLS:
-
Dynamic Light Scattering
- UV-vis:
-
Ultra-violet visible spectroscopy
- ICP-OES:
-
Inductively Coupled Plasma with Mass Optical Emission Spectroscopy
- AFM:
-
Atomic Force Microscopy
- SEM:
-
Scanning Electron Microscopy
- PVP40:
-
Polyvinylpyrrolidone
- D.I.:
-
De-ionized water
References
Cui, W., Lu, W., Zhang, Y., Lin, G., Wei, T., Jiang, L.: Gold nanoparticle ink suitable for electric-conductive pattern fabrication using in ink-jet printing technology. Colloids Surf. A Physicochem. Eng. Asp. 358(1–3), 35–41 (2010)
Khan, Y., Pavinatto, F.J., Lin, M.C., Liao, A., Swisher, S.L., Mann, K., Subramanian, V., Maharbiz, M.M., Arias, A.C.: Inkjet-printed flexible gold electrode arrays for bioelectronic interfaces. Adv. Funct. Mater. 26, 1004–1013 (2016)
Määttänen, A., Ihalainen, P., Pulkkinen, P., Wang, S., Tenhu, H., Peltonen, J.: Inkjet-printed gold electrodes on paper: characterization and functionalization. ACS Appl. Mater. Interfaces. 4(2), 955–964 (2012)
Yoshioka, Y., Jabbour, G.: Inkjet printing of oxidants for patterning of nanometer-thick conducting polymer electrodes. Adv. Mater. 18, 1307–1312 (2006)
Bietsch, A., Zhang, J., Hegner, M., Lang, H.P., Gerber, C.: Rapid functionalization of cantilever array sensors by inkjet printing. Nanotechnology 15, 873 (2004)
Jang, J.: Displays develop a new flexibility. Mater. Today 9(4), 46 (2006)
Derby, B.: Inkjet printing ceramics: from drops to solid. J. Eur. Ceram. Soc. 31, 2543–2550 (2011)
Boland, T., Xu, T., Damon, B., Cui, X.: Application of inkjet printing to tissue engineering. Biotechnol. J. 1, 910–917 (2006)
Rudolf, R., Majerić, P., Tomić, S., Shariq, M., Fercec, U., Friedrich, B., Vučevićc, D.: Morphology, aggregation properties, cytocompatibility & anti-inflammatory potential of citrate-stabilized AuNPs prepared by modular ultrasonic spray pyrolysis. J. Nanomater. 2017, 9365012 (2017)
Majerič, P., Rudolf, R., Anžel, I., Bogović, J., Stopić, S., Friedrich, B.: Synthesis of NiTi/Ni-TiO2 composite nanoparticles via ultrasonic spray pyrolysis. Mater. Technol. 49(1), 75–80 (2015)
Htay, M.T., Hashimoto, Y., Momose, N., Ito, K.: Position-selective growth of ZnO nanowires by ultrasonic spray pyrolysis. J. Cryst. Growth 311(20), 4499–4504 (2009)
Montero, M.A., Chialvo, M.R.G., Chialvo, A.C.: Preparation of gold nanoparticles supported on glassy carbon by direct spray pyrolysis. J. Mater. Chem. 19(20), 3276–3280 (2009)
Bogović, J.: Synthesis of the oxide and metal/oxide nanoparticles by the Ultrasonic Spray Pyrolysis. Ph.D. Dissertation, Faculty of the Georesources & Materials Engineering, RWTH Aachen University, Aachen (2015)
Majerič, P., Jenko, D., Friedrich, B., Rudolf, R.: Formation mechanisms for gold nanoparticles in a redesigned ultrasonic spray pyrolysis. Adv. Powder Technol. 28(3), 876–883 (2017)
Majerič, P., Jenko, D., Budič, B., Colić, M., Friedrich, B., Rudolf, R.: Formation of non-toxic Au nanoparticles with bimodal size distribution by a modular redesign of ultrasonic spray pyrolysis. Nanosci. Nanotechnol. Lett. 7(11), 1–10 (2015)
Shariq, M., Majerič, P., Friedrich, B., Budic, B., Dixit, A.R., Rudolf, R.: Application of Gold (III) Acetate as a new precursor for the synthesis of gold nanoparticles in PEG through ultrasonic spray pyrolysis. J. Clust. Sci. 28(3), 1647–1665 (2017)
Acknowledgement
The study was supported by the European Union – Erasmus Mundus Action 2 Lot 13 Euphrates Program and Slovenian Research Agency ARRS Slovenia (P2-120, Martina Program and OP20.00369).
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2019 Springer Nature Switzerland AG
About this paper
Cite this paper
Shariq, M. et al. (2019). Additive Printing of Gold Nanoparticles on Paper Substrate Through Office Ink-Jet Printer. In: Hloch, S., Klichová, D., Krolczyk, G., Chattopadhyaya, S., Ruppenthalová, L. (eds) Advances in Manufacturing Engineering and Materials. Lecture Notes in Mechanical Engineering. Springer, Cham. https://doi.org/10.1007/978-3-319-99353-9_24
Download citation
DOI: https://doi.org/10.1007/978-3-319-99353-9_24
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-99352-2
Online ISBN: 978-3-319-99353-9
eBook Packages: EngineeringEngineering (R0)